seveibar/pedometer
This hardware setup integrates a Type-C connector, battery, display, and RF antenna connected through a microcontroller, USB interface, charging and fuel gauge ICs, along with associated passive components, enabling power management, data communication, and signal processing.
- Version
- 0.4.4
- License
- unset
- Stars
- 1
validation.json
{
"timestamp": "2026-09-05T20:27:16.682Z",
"circuitSha256": "b4c11d0def2c402f709eec13556bcc44b0ba57534a634fda4a54eb1c6800727e",
"components": 52,
"traces": 138,
"vias": 122,
"errorCounts": {},
"warningCounts": {
"source_refdes_convention_warning": 3,
"source_unnamed_trace_warning": 40,
"schematic_element_outside_sheet_warning": 17,
"pcb_connector_not_in_accessible_orientation_warning": 2,
"pcb_component_missing_courtyard_warning": 1,
"supplier_footprint_mismatch_warning": 24,
"source_component_pins_underspecified_warning": 12,
"source_no_power_pin_defined_warning": 12,
"source_no_ground_pin_defined_warning": 12
},
"errors": [],
"warnings": [
{
"type": "source_refdes_convention_warning",
"warning_type": "source_refdes_convention_warning",
"message": "The \"J\" prefix is being used with a <chip />, try using it with a <connector /> or <jumper />",
"source_component_id": "source_component_26",
"refdes": "J4_SWD",
"source_component_ftype": "simple_chip",
"expected_prefixes": [
"U",
"IC"
],
"actual_prefix": "J",
"source_refdes_convention_warning_id": "source_refdes_convention_warning_3"
},
{
"type": "source_refdes_convention_warning",
"warning_type": "source_refdes_convention_warning",
"message": "The \"Q\" prefix is being used with a <chip />, try using it with a <transistor />",
"source_component_id": "source_component_27",
"refdes": "Q1_DISPLAY_SWITCH",
"source_component_ftype": "simple_chip",
"expected_prefixes": [
"U",
"IC"
],
"actual_prefix": "Q",
"source_refdes_convention_warning_id": "source_refdes_convention_warning_4"
},
{
"type": "source_refdes_convention_warning",
"warning_type": "source_refdes_convention_warning",
"message": "The \"Y\" prefix is being used with a <chip />, try using it with a <crystal />",
"source_component_id": "source_component_28",
"refdes": "Y1_48MHZ",
"source_component_ftype": "simple_chip",
"expected_prefixes": [
"U",
"IC"
],
"actual_prefix": "Y",
"source_refdes_convention_warning_id": "source_refdes_convention_warning_5"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_0",
"message": "<trace#598(from:.J1_USB_C > .GND1 to:.J1_USB_C > .EH3) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_8",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_1",
"message": "<trace#599(from:.J1_USB_C > .GND2 to:.J1_USB_C > .EH4) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_9",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_2",
"message": "<trace#604(from:.J1_USB_C > .CC1 to:.R1_CC1 > .pin1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_14",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_3",
"message": "<trace#606(from:.J1_USB_C > .CC2 to:.R2_CC2 > .pin1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_16",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_4",
"message": "<trace#614(from:.U2_CHARGER > .PMID2 to:.U2_CHARGER > .PMID1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_24",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_5",
"message": "<trace#615(from:.C2_PMID > .pin1 to:.C3_VINLS > .pin1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_25",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_6",
"message": "<trace#617(from:.U2_CHARGER > .VINLS to:.U2_CHARGER > .PMID2) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_27",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_7",
"message": "<trace#618(from:.C3_VINLS > .pin1 to:.U2_CHARGER > .PMID1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_28",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_8",
"message": "<trace#619(from:.C3_VINLS > .pin2 to:.U2_CHARGER > .GND) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_29",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_9",
"message": "<trace#621(from:.U2_CHARGER > .BAT2 to:.U2_CHARGER > .BAT1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_31",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_10",
"message": "<trace#624(from:.U2_CHARGER > .VDD to:.C5_CHG_VDD > .pin1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_34",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_11",
"message": "<trace#632(from:.U2_CHARGER > .IMAX to:.R3_IMAX > .pin1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_42",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_12",
"message": "<trace#639(from:.U2_CHARGER > .LP to:.R7_LP_BOOT_PD > .pin1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_49",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_13",
"message": "<trace#647(from:.U2_CHARGER > .MR to:.SW1_WAKE > .pin1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_57",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_14",
"message": "<trace#649(from:.SW1_WAKE > .pin2 to:.SW1_WAKE > .pin1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_59",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_15",
"message": "<trace#659(from:.U3_GAUGE > .BIN to:.R9_BIN_PD > .pin1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_69",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_16",
"message": "<trace#661(from:.U3_GAUGE > .BAT to:.C7_GAUGE_BAT > .pin1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_71",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_17",
"message": "<trace#663(from:.U3_GAUGE > .VDD to:.C8_GAUGE_VDD > .pin1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_73",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_18",
"message": "<trace#666(from:.U3_GAUGE > .SDA to:.U4_ACCEL > .SDX) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_76",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_19",
"message": "<trace#667(from:.U3_GAUGE > .GPOUT to:.R10_GAUGE_INT_PU > .pin1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_77",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_20",
"message": "<trace#671(from:.U1_MCU > .VDDS2 to:.U1_MCU > .VDDS1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_81",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_21",
"message": "<trace#672(from:.U1_MCU > .VDDS3 to:.U1_MCU > .VDDS1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_82",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_22",
"message": "<trace#674(from:.U1_MCU > .EP to:.U1_MCU > .GND) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_84",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_23",
"message": "<trace#677(from:.U1_MCU > .DCDC to:.L1_DCDC > .pin1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_87",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_24",
"message": "<trace#685(from:.U1_MCU > .VDDD to:.C12_VDDD > .pin1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_95",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_25",
"message": "<trace#686(from:.C12_VDDD > .pin2 to:.C11_VDDR_100N > .pin2) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_96",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_26",
"message": "<trace#695(from:.U1_MCU > .X48P to:.Y1_48MHZ > .XIN) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_105",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_27",
"message": "<trace#696(from:.U1_MCU > .X48N to:.Y1_48MHZ > .XOUT) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_106",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_28",
"message": "<trace#698(from:.U1_MCU > .EP to:.Y1_48MHZ > .GND2) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_108",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_29",
"message": "<trace#705(from:.U1_MCU > .DIO17_SWDCK to:.J4_SWD > .SWDCK) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_115",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_30",
"message": "<trace#710(from:.U1_MCU > .DIO20_A11 to:.Q1_DISPLAY_SWITCH > .G) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_120",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_31",
"message": "<trace#717(from:.U4_ACCEL > .VDDIO to:.U4_ACCEL > .VDD) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_127",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_32",
"message": "<trace#721(from:.U4_ACCEL > .SDO to:.U4_ACCEL > .GNDIO) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_131",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_33",
"message": "<trace#730(from:.R12_I2C_SCL > .pin2 to:.R10_GAUGE_INT_PU > .pin2) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_140",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_34",
"message": "<trace#747(from:.U1_MCU > .ANT to:.C21_RF_SHUNT1 > .pin1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_157",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_35",
"message": "<trace#748(from:.C21_RF_SHUNT1 > .pin1 to:.L2_RF_SERIES > .pin1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_158",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_36",
"message": "<trace#749(from:.U1_MCU > .GND to:.C21_RF_SHUNT1 > .pin2) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_159",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_37",
"message": "<trace#750(from:.L2_RF_SERIES > .pin2 to:.C22_RF_SHUNT2 > .pin1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_160",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_38",
"message": "<trace#751(from:.C22_RF_SHUNT2 > .pin1 to:.C24_RF_DC_BLOCK > .pin1) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_161",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "source_unnamed_trace_warning",
"source_unnamed_trace_warning_id": "source_unnamed_trace_warning_39",
"message": "<trace#753(from:.C24_RF_DC_BLOCK > .pin2 to:.ANT1 > .FEED) /> is missing a name. Add a name prop to make the trace easier to identify.",
"source_trace_id": "source_trace_163",
"subcircuit_id": "subcircuit_source_group_4",
"warning_type": "source_unnamed_trace_warning"
},
{
"type": "schematic_element_outside_sheet_warning",
"schematic_element_outside_sheet_warning_id": "schematic_element_outside_sheet_warning_0",
"warning_type": "schematic_element_outside_sheet_warning",
"message": "schematic_component schematic_component_37 extends outside the drawing area of schematic sheet \"BLE, Sensors and Display\"",
"schematic_sheet_id": "schematic_sheet_1",
"schematic_element_type": "schematic_component",
"schematic_element_id": "schematic_component_37"
},
{
"type": "schematic_element_outside_sheet_warning",
"schematic_element_outside_sheet_warning_id": "schematic_element_outside_sheet_warning_1",
"warning_type": "schematic_element_outside_sheet_warning",
"message": "schematic_component schematic_component_40 extends outside the drawing area of schematic sheet \"BLE, Sensors and Display\"",
"schematic_sheet_id": "schematic_sheet_1",
"schematic_element_type": "schematic_component",
"schematic_element_id": "schematic_component_40"
},
{
"type": "schematic_element_outside_sheet_warning",
"schematic_element_outside_sheet_warning_id": "schematic_element_outside_sheet_warning_2",
"warning_type": "schematic_element_outside_sheet_warning",
"message": "schematic_net_label schematic_net_label_62 extends outside the drawing area of schematic sheet \"BLE, Sensors and Display\"",
"schematic_sheet_id": "schematic_sheet_1",
"schematic_element_type": "schematic_net_label",
"schematic_element_id": "schematic_net_label_62"
},
{
"type": "schematic_element_outside_sheet_warning",
"schematic_element_outside_sheet_warning_id": "schematic_element_outside_sheet_warning_3",
"warning_type": "schematic_element_outside_sheet_warning",
"message": "schematic_net_label schematic_net_label_72 extends outside the drawing area of schematic sheet \"BLE, Sensors and Display\"",
"schematic_sheet_id": "schematic_sheet_1",
"schematic_element_type": "schematic_net_label",
"schematic_element_id": "schematic_net_label_72"
},
{
"type": "schematic_element_outside_sheet_warning",
"schematic_element_outside_sheet_warning_id": "schematic_element_outside_sheet_warning_4",
"warning_type": "schematic_element_outside_sheet_warning",
"message": "schematic_net_label schematic_net_label_74 extends outside the drawing area of schematic sheet \"BLE, Sensors and Display\"",
"schematic_sheet_id": "schematic_sheet_1",
"schematic_element_type": "schematic_net_label",
"schematic_element_id": "schematic_net_label_74"
},
{
"type": "schematic_element_outside_sheet_warning",
"schematic_element_outside_sheet_warning_id": "schematic_element_outside_sheet_warning_5",
"warning_type": "schematic_element_outside_sheet_warning",
"message": "schematic_net_label schematic_net_label_88 extends outside the drawing area of schematic sheet \"BLE, Sensors and Display\"",
"schematic_sheet_id": "schematic_sheet_1",
"schematic_element_type": "schematic_net_label",
"schematic_element_id": "schematic_net_label_88"
},
{
"type": "schematic_element_outside_sheet_warning",
"schematic_element_outside_sheet_warning_id": "schematic_element_outside_sheet_warning_6",
"warning_type": "schematic_element_outside_sheet_warning",
"message": "schematic_net_label schematic_net_label_92 extends outside the drawing area of schematic sheet \"BLE, Sensors and Display\"",
"schematic_sheet_id": "schematic_sheet_1",
"schematic_element_type": "schematic_net_label",
"schematic_element_id": "schematic_net_label_92"
},
{
"type": "schematic_element_outside_sheet_warning",
"schematic_element_outside_sheet_warning_id": "schematic_element_outside_sheet_warning_7",
"warning_type": "schematic_element_outside_sheet_warning",
"message": "schematic_net_label schematic_net_label_100 extends outside the drawing area of schematic sheet \"BLE, Sensors and Display\"",
"schematic_sheet_id": "schematic_sheet_1",
"schematic_element_type": "schematic_net_label",
"schematic_element_id": "schematic_net_label_100"
},
{
"type": "schematic_element_outside_sheet_warning",
"schematic_element_outside_sheet_warning_id": "schematic_element_outside_sheet_warning_8",
"warning_type": "schematic_element_outside_sheet_warning",
"message": "schematic_net_label schematic_net_label_104 extends outside the drawing area of schematic sheet \"BLE, Sensors and Display\"",
"schematic_sheet_id": "schematic_sheet_1",
"schematic_element_type": "schematic_net_label",
"schematic_element_id": "schematic_net_label_104"
},
{
"type": "schematic_element_outside_sheet_warning",
"schematic_element_outside_sheet_warning_id": "schematic_element_outside_sheet_warning_9",
"warning_type": "schematic_element_outside_sheet_warning",
"message": "schematic_trace schematic_trace_31 extends outside the drawing area of schematic sheet \"BLE, Sensors and Display\"",
"schematic_sheet_id": "schematic_sheet_1",
"schematic_element_type": "schematic_trace",
"schematic_element_id": "schematic_trace_31"
},
{
"type": "schematic_element_outside_sheet_warning",
"schematic_element_outside_sheet_warning_id": "schematic_element_outside_sheet_warning_10",
"warning_type": "schematic_element_outside_sheet_warning",
"message": "schematic_trace schematic_trace_32 extends outside the drawing area of schematic sheet \"BLE, Sensors and Display\"",
"schematic_sheet_id": "schematic_sheet_1",
"schematic_element_type": "schematic_trace",
"schematic_element_id": "schematic_trace_32"
},
{
"type": "schematic_element_outside_sheet_warning",
"schematic_element_outside_sheet_warning_id": "schematic_element_outside_sheet_warning_11",
"warning_type": "schematic_element_outside_sheet_warning",
"message": "schematic_trace schematic_trace_43 extends outside the drawing area of schematic sheet \"BLE, Sensors and Display\"",
"schematic_sheet_id": "schematic_sheet_1",
"schematic_element_type": "schematic_trace",
"schematic_element_id": "schematic_trace_43"
},
{
"type": "schematic_element_outside_sheet_warning",
"schematic_element_outside_sheet_warning_id": "schematic_element_outside_sheet_warning_12",
"warning_type": "schematic_element_outside_sheet_warning",
"message": "schematic_trace schematic_trace_46 extends outside the drawing area of schematic sheet \"BLE, Sensors and Display\"",
"schematic_sheet_id": "schematic_sheet_1",
"schematic_element_type": "schematic_trace",
"schematic_element_id": "schematic_trace_46"
},
{
"type": "schematic_element_outside_sheet_warning",
"schematic_element_outside_sheet_warning_id": "schematic_element_outside_sheet_warning_13",
"warning_type": "schematic_element_outside_sheet_warning",
"message": "schematic_trace schematic_trace_51 extends outside the drawing area of schematic sheet \"BLE, Sensors and Display\"",
"schematic_sheet_id": "schematic_sheet_1",
"schematic_element_type": "schematic_trace",
"schematic_element_id": "schematic_trace_51"
},
{
"type": "schematic_element_outside_sheet_warning",
"schematic_element_outside_sheet_warning_id": "schematic_element_outside_sheet_warning_14",
"warning_type": "schematic_element_outside_sheet_warning",
"message": "schematic_trace schematic_trace_52 extends outside the drawing area of schematic sheet \"BLE, Sensors and Display\"",
"schematic_sheet_id": "schematic_sheet_1",
"schematic_element_type": "schematic_trace",
"schematic_element_id": "schematic_trace_52"
},
{
"type": "schematic_element_outside_sheet_warning",
"schematic_element_outside_sheet_warning_id": "schematic_element_outside_sheet_warning_15",
"warning_type": "schematic_element_outside_sheet_warning",
"message": "schematic_trace schematic_trace_56 extends outside the drawing area of schematic sheet \"BLE, Sensors and Display\"",
"schematic_sheet_id": "schematic_sheet_1",
"schematic_element_type": "schematic_trace",
"schematic_element_id": "schematic_trace_56"
},
{
"type": "schematic_element_outside_sheet_warning",
"schematic_element_outside_sheet_warning_id": "schematic_element_outside_sheet_warning_16",
"warning_type": "schematic_element_outside_sheet_warning",
"message": "schematic_trace schematic_trace_68 extends outside the drawing area of schematic sheet \"BLE, Sensors and Display\"",
"schematic_sheet_id": "schematic_sheet_1",
"schematic_element_type": "schematic_trace",
"schematic_element_id": "schematic_trace_68"
},
{
"type": "pcb_connector_not_in_accessible_orientation_warning",
"warning_type": "pcb_connector_not_in_accessible_orientation_warning",
"pcb_connector_not_in_accessible_orientation_warning_id": "pcb_connector_not_in_accessible_orientation_warning_0",
"message": "component is facing y- but should face x- so the connector is accessible from the board edge",
"pcb_component_id": "pcb_component_1",
"source_component_id": "source_component_1",
"pcb_board_id": "pcb_board_0",
"facing_direction": "y-",
"recommended_facing_direction": "x-",
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "pcb_connector_not_in_accessible_orientation_warning",
"warning_type": "pcb_connector_not_in_accessible_orientation_warning",
"pcb_connector_not_in_accessible_orientation_warning_id": "pcb_connector_not_in_accessible_orientation_warning_1",
"message": "component is facing y- but should face y+ so the connector is accessible from the board edge",
"pcb_component_id": "pcb_component_2",
"source_component_id": "source_component_2",
"pcb_board_id": "pcb_board_0",
"facing_direction": "y-",
"recommended_facing_direction": "y+",
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "pcb_component_missing_courtyard_warning",
"pcb_component_missing_courtyard_warning_id": "pcb_component_missing_courtyard_warning_pcb_component_51",
"warning_type": "pcb_component_missing_courtyard_warning",
"message": "TP6_PG has no courtyard",
"pcb_component_id": "pcb_component_51",
"source_component_id": "source_component_51",
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_aSZjPH2ur5",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<resistor#465(.PedometerBoard>.R11_RESET_PU) /> footprint \"0402\" does not match supplier footprint jlcpcb:C25741 (copper IoU 0.7741).",
"source_component_id": "source_component_38",
"pcb_component_id": "pcb_component_38",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C25741",
"footprint_copper_intersection_over_union": 0.7741
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_GWemQit6Ho",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<resistor#553(.PedometerBoard>.R15_DISPLAY_GATE_PU) /> footprint \"0402\" does not match supplier footprint jlcpcb:C25741 (copper IoU 0.7741).",
"source_component_id": "source_component_45",
"pcb_component_id": "pcb_component_45",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C25741",
"footprint_copper_intersection_over_union": 0.7741
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_sbquJLiG7k",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<capacitor#138(.PedometerBoard>.C4_VSYS_SENSE) /> footprint \"0402\" does not match supplier footprint jlcpcb:C5137473 (copper IoU 0.7249).",
"source_component_id": "source_component_11",
"pcb_component_id": "pcb_component_11",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C5137473",
"footprint_copper_intersection_over_union": 0.7249
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_PztjY67Neb",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<resistor#300(.PedometerBoard>.R9_BIN_PD) /> footprint \"0402\" does not match supplier footprint jlcpcb:C25744 (copper IoU 0.7741).",
"source_component_id": "source_component_24",
"pcb_component_id": "pcb_component_24",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C25744",
"footprint_copper_intersection_over_union": 0.7741
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_94Y0eBBrnr",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<capacitor#478(.PedometerBoard>.C17_RESET) /> footprint \"0402\" does not match supplier footprint jlcpcb:C1525 (copper IoU 0.7249).",
"source_component_id": "source_component_39",
"pcb_component_id": "pcb_component_39",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C1525",
"footprint_copper_intersection_over_union": 0.7249
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_lFVx9EOmQp",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<capacitor#393(.PedometerBoard>.C11_VDDR_100N) /> footprint \"0402\" does not match supplier footprint jlcpcb:C1525 (copper IoU 0.7249).",
"source_component_id": "source_component_32",
"pcb_component_id": "pcb_component_32",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C1525",
"footprint_copper_intersection_over_union": 0.7249
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_8P7uSz5s45",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<resistor#174(.PedometerBoard>.R3_IMAX) /> footprint \"0402\" does not match supplier footprint jlcpcb:C25744 (copper IoU 0.7741).",
"source_component_id": "source_component_14",
"pcb_component_id": "pcb_component_14",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C25744",
"footprint_copper_intersection_over_union": 0.7741
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_ZlNHE14DvE",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<capacitor#503(.sensor_region>.C18_ACCEL_VDD) /> footprint \"0402\" does not match supplier footprint jlcpcb:C1525 (copper IoU 0.7249).",
"source_component_id": "source_component_41",
"pcb_component_id": "pcb_component_41",
"pcb_group_id": "pcb_group_3",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C1525",
"footprint_copper_intersection_over_union": 0.7249
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_b73lJmjJE7",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<resistor#46(.PedometerBoard>.R1_CC1) /> footprint \"0402\" does not match supplier footprint jlcpcb:C25905 (copper IoU 0.7741).",
"source_component_id": "source_component_3",
"pcb_component_id": "pcb_component_3",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C25905",
"footprint_copper_intersection_over_union": 0.7741
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_MRPiLvZvoy",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<resistor#213(.PedometerBoard>.R7_LP_BOOT_PD) /> footprint \"0402\" does not match supplier footprint jlcpcb:C25741 (copper IoU 0.7741).",
"source_component_id": "source_component_17",
"pcb_component_id": "pcb_component_17",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C25741",
"footprint_copper_intersection_over_union": 0.7741
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_hvG9oVMhyV",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<capacitor#288(.PedometerBoard>.C8_GAUGE_VDD) /> footprint \"0402\" does not match supplier footprint jlcpcb:C12530 (copper IoU 0.7249).",
"source_component_id": "source_component_23",
"pcb_component_id": "pcb_component_23",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C12530",
"footprint_copper_intersection_over_union": 0.7249
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_rcUtysN5Kx",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<capacitor#405(.PedometerBoard>.C12_VDDD) /> footprint \"0402\" does not match supplier footprint jlcpcb:C5137473 (copper IoU 0.7249).",
"source_component_id": "source_component_33",
"pcb_component_id": "pcb_component_33",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C5137473",
"footprint_copper_intersection_over_union": 0.7249
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_EN2B6PbAXC",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<capacitor#441(.PedometerBoard>.C15_VDDS_3) /> footprint \"0402\" does not match supplier footprint jlcpcb:C1525 (copper IoU 0.7249).",
"source_component_id": "source_component_36",
"pcb_component_id": "pcb_component_36",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C1525",
"footprint_copper_intersection_over_union": 0.7249
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_TjplPT4HvS",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<capacitor#515(.sensor_region>.C19_ACCEL_VDDIO) /> footprint \"0402\" does not match supplier footprint jlcpcb:C1525 (copper IoU 0.7249).",
"source_component_id": "source_component_42",
"pcb_component_id": "pcb_component_42",
"pcb_group_id": "pcb_group_3",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C1525",
"footprint_copper_intersection_over_union": 0.7249
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_SHnDU0CqgV",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<capacitor#276(.PedometerBoard>.C7_GAUGE_BAT) /> footprint \"0402\" does not match supplier footprint jlcpcb:C5137473 (copper IoU 0.7249).",
"source_component_id": "source_component_22",
"pcb_component_id": "pcb_component_22",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C5137473",
"footprint_copper_intersection_over_union": 0.7249
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_85hNfj9NFQ",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<capacitor#429(.PedometerBoard>.C14_VDDS_2) /> footprint \"0402\" does not match supplier footprint jlcpcb:C1525 (copper IoU 0.7249).",
"source_component_id": "source_component_35",
"pcb_component_id": "pcb_component_35",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C1525",
"footprint_copper_intersection_over_union": 0.7249
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_OjW3JBDuhD",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<capacitor#417(.PedometerBoard>.C13_VDDS_1) /> footprint \"0402\" does not match supplier footprint jlcpcb:C1525 (copper IoU 0.7249).",
"source_component_id": "source_component_34",
"pcb_component_id": "pcb_component_34",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C1525",
"footprint_copper_intersection_over_union": 0.7249
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_CujqQcJsQU",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<chip#351(.mcu_region>.Y1_48MHZ) /> footprint the provided footprint does not match supplier footprint jlcpcb:C1985532 (copper IoU 0.6379).",
"source_component_id": "source_component_28",
"pcb_component_id": "pcb_component_28",
"pcb_group_id": "pcb_group_2",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C1985532",
"footprint_copper_intersection_over_union": 0.6379
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_lBjTSQdDNM",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<resistor#262(.gauge_region>.R12_I2C_SCL) /> footprint \"0402\" does not match supplier footprint jlcpcb:C25744 (copper IoU 0.7741).",
"source_component_id": "source_component_21",
"pcb_component_id": "pcb_component_21",
"pcb_group_id": "pcb_group_1",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C25744",
"footprint_copper_intersection_over_union": 0.7741
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_mLY87Nnx0e",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<resistor#528(.PedometerBoard>.R13_I2C_SDA) /> footprint \"0402\" does not match supplier footprint jlcpcb:C25744 (copper IoU 0.7741).",
"source_component_id": "source_component_43",
"pcb_component_id": "pcb_component_43",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C25744",
"footprint_copper_intersection_over_union": 0.7741
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_JFs5nfpyFG",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<resistor#59(.PedometerBoard>.R2_CC2) /> footprint \"0402\" does not match supplier footprint jlcpcb:C25905 (copper IoU 0.7741).",
"source_component_id": "source_component_4",
"pcb_component_id": "pcb_component_4",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C25905",
"footprint_copper_intersection_over_union": 0.7741
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_4xWGzCujSS",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<resistor#187(.PedometerBoard>.R4_TS_BIAS) /> footprint \"0402\" does not match supplier footprint jlcpcb:C25744 (copper IoU 0.7741).",
"source_component_id": "source_component_15",
"pcb_component_id": "pcb_component_15",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C25744",
"footprint_copper_intersection_over_union": 0.7741
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_hpeywrnvQ7",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<capacitor#381(.PedometerBoard>.C10_VDDR_1U) /> footprint \"0402\" does not match supplier footprint jlcpcb:C5137473 (copper IoU 0.7249).",
"source_component_id": "source_component_31",
"pcb_component_id": "pcb_component_31",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C5137473",
"footprint_copper_intersection_over_union": 0.7249
},
{
"type": "supplier_footprint_mismatch_warning",
"supplier_footprint_mismatch_warning_id": "supplier_footprint_mismatch_warning_tsNWbAffP7",
"warning_type": "supplier_footprint_mismatch_warning",
"message": "<resistor#226(.PedometerBoard>.R8_PG_PU) /> footprint \"0402\" does not match supplier footprint jlcpcb:C25741 (copper IoU 0.7741).",
"source_component_id": "source_component_18",
"pcb_component_id": "pcb_component_18",
"subcircuit_id": "subcircuit_source_group_4",
"supplier_name": "jlcpcb",
"supplier_part_number": "C25741",
"footprint_copper_intersection_over_union": 0.7741
},
{
"type": "source_component_pins_underspecified_warning",
"source_component_pins_underspecified_warning_id": "source_component_pins_underspecified_warning_source_component_0",
"warning_type": "source_component_pins_underspecified_warning",
"message": "All pins on J1_USB_C are underspecified (no pinAttributes set)",
"source_component_id": "source_component_0",
"source_port_ids": [
"source_port_0",
"source_port_1",
"source_port_2",
"source_port_3",
"source_port_4",
"source_port_5",
"source_port_6",
"source_port_7",
"source_port_8",
"source_port_9"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_component_pins_underspecified_warning",
"source_component_pins_underspecified_warning_id": "source_component_pins_underspecified_warning_source_component_1",
"warning_type": "source_component_pins_underspecified_warning",
"message": "All pins on J2_BATTERY are underspecified (no pinAttributes set)",
"source_component_id": "source_component_1",
"source_port_ids": [
"source_port_10",
"source_port_11",
"source_port_12",
"source_port_13",
"source_port_14"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_component_pins_underspecified_warning",
"source_component_pins_underspecified_warning_id": "source_component_pins_underspecified_warning_source_component_2",
"warning_type": "source_component_pins_underspecified_warning",
"message": "All pins on J3_DISPLAY are underspecified (no pinAttributes set)",
"source_component_id": "source_component_2",
"source_port_ids": [
"source_port_15",
"source_port_16",
"source_port_17",
"source_port_18",
"source_port_19",
"source_port_20",
"source_port_21",
"source_port_22",
"source_port_23"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_component_pins_underspecified_warning",
"source_component_pins_underspecified_warning_id": "source_component_pins_underspecified_warning_source_component_5",
"warning_type": "source_component_pins_underspecified_warning",
"message": "All pins on D1_VBUS_TVS are underspecified (no pinAttributes set)",
"source_component_id": "source_component_5",
"source_port_ids": [
"source_port_28",
"source_port_29"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_component_pins_underspecified_warning",
"source_component_pins_underspecified_warning_id": "source_component_pins_underspecified_warning_source_component_7",
"warning_type": "source_component_pins_underspecified_warning",
"message": "All pins on U2_CHARGER are underspecified (no pinAttributes set)",
"source_component_id": "source_component_7",
"source_port_ids": [
"source_port_32",
"source_port_33",
"source_port_34",
"source_port_35",
"source_port_36",
"source_port_37",
"source_port_38",
"source_port_39",
"source_port_40",
"source_port_41",
"source_port_42",
"source_port_43",
"source_port_44",
"source_port_45",
"source_port_46",
"source_port_47",
"source_port_48",
"source_port_49",
"source_port_50",
"source_port_51"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_component_pins_underspecified_warning",
"source_component_pins_underspecified_warning_id": "source_component_pins_underspecified_warning_source_component_19",
"warning_type": "source_component_pins_underspecified_warning",
"message": "All pins on U3_GAUGE are underspecified (no pinAttributes set)",
"source_component_id": "source_component_19",
"source_port_ids": [
"source_port_76",
"source_port_77",
"source_port_78",
"source_port_79",
"source_port_80",
"source_port_81",
"source_port_82",
"source_port_83",
"source_port_84"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_component_pins_underspecified_warning",
"source_component_pins_underspecified_warning_id": "source_component_pins_underspecified_warning_source_component_25",
"warning_type": "source_component_pins_underspecified_warning",
"message": "All pins on U1_MCU are underspecified (no pinAttributes set)",
"source_component_id": "source_component_25",
"source_port_ids": [
"source_port_95",
"source_port_96",
"source_port_97",
"source_port_98",
"source_port_99",
"source_port_100",
"source_port_101",
"source_port_102",
"source_port_103",
"source_port_104",
"source_port_105",
"source_port_106",
"source_port_107",
"source_port_108",
"source_port_109",
"source_port_110",
"source_port_111",
"source_port_112",
"source_port_113",
"source_port_114",
"source_port_115",
"source_port_116",
"source_port_117",
"source_port_118",
"source_port_119"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_component_pins_underspecified_warning",
"source_component_pins_underspecified_warning_id": "source_component_pins_underspecified_warning_source_component_26",
"warning_type": "source_component_pins_underspecified_warning",
"message": "All pins on J4_SWD are underspecified (no pinAttributes set)",
"source_component_id": "source_component_26",
"source_port_ids": [
"source_port_120",
"source_port_121",
"source_port_122",
"source_port_123",
"source_port_124",
"source_port_125",
"source_port_126"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_component_pins_underspecified_warning",
"source_component_pins_underspecified_warning_id": "source_component_pins_underspecified_warning_source_component_27",
"warning_type": "source_component_pins_underspecified_warning",
"message": "All pins on Q1_DISPLAY_SWITCH are underspecified (no pinAttributes set)",
"source_component_id": "source_component_27",
"source_port_ids": [
"source_port_127",
"source_port_128",
"source_port_129"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_component_pins_underspecified_warning",
"source_component_pins_underspecified_warning_id": "source_component_pins_underspecified_warning_source_component_28",
"warning_type": "source_component_pins_underspecified_warning",
"message": "All pins on Y1_48MHZ are underspecified (no pinAttributes set)",
"source_component_id": "source_component_28",
"source_port_ids": [
"source_port_130",
"source_port_131",
"source_port_132",
"source_port_133"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_component_pins_underspecified_warning",
"source_component_pins_underspecified_warning_id": "source_component_pins_underspecified_warning_source_component_40",
"warning_type": "source_component_pins_underspecified_warning",
"message": "All pins on U4_ACCEL are underspecified (no pinAttributes set)",
"source_component_id": "source_component_40",
"source_port_ids": [
"source_port_156",
"source_port_157",
"source_port_158",
"source_port_159",
"source_port_160",
"source_port_161",
"source_port_162",
"source_port_163",
"source_port_164",
"source_port_165",
"source_port_166",
"source_port_167"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_component_pins_underspecified_warning",
"source_component_pins_underspecified_warning_id": "source_component_pins_underspecified_warning_source_component_50",
"warning_type": "source_component_pins_underspecified_warning",
"message": "All pins on ANT1 are underspecified (no pinAttributes set)",
"source_component_id": "source_component_50",
"source_port_ids": [
"source_port_186",
"source_port_187"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_power_pin_defined_warning",
"source_no_power_pin_defined_warning_id": "source_no_power_pin_defined_warning_source_component_0",
"warning_type": "source_no_power_pin_defined_warning",
"message": "J1_USB_C has no pin with requires_power=true",
"source_component_id": "source_component_0",
"source_port_ids": [
"source_port_0",
"source_port_1",
"source_port_2",
"source_port_3",
"source_port_4",
"source_port_5",
"source_port_6",
"source_port_7",
"source_port_8",
"source_port_9"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_power_pin_defined_warning",
"source_no_power_pin_defined_warning_id": "source_no_power_pin_defined_warning_source_component_1",
"warning_type": "source_no_power_pin_defined_warning",
"message": "J2_BATTERY has no pin with requires_power=true",
"source_component_id": "source_component_1",
"source_port_ids": [
"source_port_10",
"source_port_11",
"source_port_12",
"source_port_13",
"source_port_14"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_power_pin_defined_warning",
"source_no_power_pin_defined_warning_id": "source_no_power_pin_defined_warning_source_component_2",
"warning_type": "source_no_power_pin_defined_warning",
"message": "J3_DISPLAY has no pin with requires_power=true",
"source_component_id": "source_component_2",
"source_port_ids": [
"source_port_15",
"source_port_16",
"source_port_17",
"source_port_18",
"source_port_19",
"source_port_20",
"source_port_21",
"source_port_22",
"source_port_23"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_power_pin_defined_warning",
"source_no_power_pin_defined_warning_id": "source_no_power_pin_defined_warning_source_component_5",
"warning_type": "source_no_power_pin_defined_warning",
"message": "D1_VBUS_TVS has no pin with requires_power=true",
"source_component_id": "source_component_5",
"source_port_ids": [
"source_port_28",
"source_port_29"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_power_pin_defined_warning",
"source_no_power_pin_defined_warning_id": "source_no_power_pin_defined_warning_source_component_7",
"warning_type": "source_no_power_pin_defined_warning",
"message": "U2_CHARGER has no pin with requires_power=true",
"source_component_id": "source_component_7",
"source_port_ids": [
"source_port_32",
"source_port_33",
"source_port_34",
"source_port_35",
"source_port_36",
"source_port_37",
"source_port_38",
"source_port_39",
"source_port_40",
"source_port_41",
"source_port_42",
"source_port_43",
"source_port_44",
"source_port_45",
"source_port_46",
"source_port_47",
"source_port_48",
"source_port_49",
"source_port_50",
"source_port_51"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_power_pin_defined_warning",
"source_no_power_pin_defined_warning_id": "source_no_power_pin_defined_warning_source_component_19",
"warning_type": "source_no_power_pin_defined_warning",
"message": "U3_GAUGE has no pin with requires_power=true",
"source_component_id": "source_component_19",
"source_port_ids": [
"source_port_76",
"source_port_77",
"source_port_78",
"source_port_79",
"source_port_80",
"source_port_81",
"source_port_82",
"source_port_83",
"source_port_84"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_power_pin_defined_warning",
"source_no_power_pin_defined_warning_id": "source_no_power_pin_defined_warning_source_component_25",
"warning_type": "source_no_power_pin_defined_warning",
"message": "U1_MCU has no pin with requires_power=true",
"source_component_id": "source_component_25",
"source_port_ids": [
"source_port_95",
"source_port_96",
"source_port_97",
"source_port_98",
"source_port_99",
"source_port_100",
"source_port_101",
"source_port_102",
"source_port_103",
"source_port_104",
"source_port_105",
"source_port_106",
"source_port_107",
"source_port_108",
"source_port_109",
"source_port_110",
"source_port_111",
"source_port_112",
"source_port_113",
"source_port_114",
"source_port_115",
"source_port_116",
"source_port_117",
"source_port_118",
"source_port_119"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_power_pin_defined_warning",
"source_no_power_pin_defined_warning_id": "source_no_power_pin_defined_warning_source_component_26",
"warning_type": "source_no_power_pin_defined_warning",
"message": "J4_SWD has no pin with requires_power=true",
"source_component_id": "source_component_26",
"source_port_ids": [
"source_port_120",
"source_port_121",
"source_port_122",
"source_port_123",
"source_port_124",
"source_port_125",
"source_port_126"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_power_pin_defined_warning",
"source_no_power_pin_defined_warning_id": "source_no_power_pin_defined_warning_source_component_27",
"warning_type": "source_no_power_pin_defined_warning",
"message": "Q1_DISPLAY_SWITCH has no pin with requires_power=true",
"source_component_id": "source_component_27",
"source_port_ids": [
"source_port_127",
"source_port_128",
"source_port_129"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_power_pin_defined_warning",
"source_no_power_pin_defined_warning_id": "source_no_power_pin_defined_warning_source_component_28",
"warning_type": "source_no_power_pin_defined_warning",
"message": "Y1_48MHZ has no pin with requires_power=true",
"source_component_id": "source_component_28",
"source_port_ids": [
"source_port_130",
"source_port_131",
"source_port_132",
"source_port_133"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_power_pin_defined_warning",
"source_no_power_pin_defined_warning_id": "source_no_power_pin_defined_warning_source_component_40",
"warning_type": "source_no_power_pin_defined_warning",
"message": "U4_ACCEL has no pin with requires_power=true",
"source_component_id": "source_component_40",
"source_port_ids": [
"source_port_156",
"source_port_157",
"source_port_158",
"source_port_159",
"source_port_160",
"source_port_161",
"source_port_162",
"source_port_163",
"source_port_164",
"source_port_165",
"source_port_166",
"source_port_167"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_power_pin_defined_warning",
"source_no_power_pin_defined_warning_id": "source_no_power_pin_defined_warning_source_component_50",
"warning_type": "source_no_power_pin_defined_warning",
"message": "ANT1 has no pin with requires_power=true",
"source_component_id": "source_component_50",
"source_port_ids": [
"source_port_186",
"source_port_187"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_ground_pin_defined_warning",
"source_no_ground_pin_defined_warning_id": "source_no_ground_pin_defined_warning_source_component_0",
"warning_type": "source_no_ground_pin_defined_warning",
"message": "J1_USB_C has no pin with requires_ground=true",
"source_component_id": "source_component_0",
"source_port_ids": [
"source_port_0",
"source_port_1",
"source_port_2",
"source_port_3",
"source_port_4",
"source_port_5",
"source_port_6",
"source_port_7",
"source_port_8",
"source_port_9"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_ground_pin_defined_warning",
"source_no_ground_pin_defined_warning_id": "source_no_ground_pin_defined_warning_source_component_1",
"warning_type": "source_no_ground_pin_defined_warning",
"message": "J2_BATTERY has no pin with requires_ground=true",
"source_component_id": "source_component_1",
"source_port_ids": [
"source_port_10",
"source_port_11",
"source_port_12",
"source_port_13",
"source_port_14"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_ground_pin_defined_warning",
"source_no_ground_pin_defined_warning_id": "source_no_ground_pin_defined_warning_source_component_2",
"warning_type": "source_no_ground_pin_defined_warning",
"message": "J3_DISPLAY has no pin with requires_ground=true",
"source_component_id": "source_component_2",
"source_port_ids": [
"source_port_15",
"source_port_16",
"source_port_17",
"source_port_18",
"source_port_19",
"source_port_20",
"source_port_21",
"source_port_22",
"source_port_23"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_ground_pin_defined_warning",
"source_no_ground_pin_defined_warning_id": "source_no_ground_pin_defined_warning_source_component_5",
"warning_type": "source_no_ground_pin_defined_warning",
"message": "D1_VBUS_TVS has no pin with requires_ground=true",
"source_component_id": "source_component_5",
"source_port_ids": [
"source_port_28",
"source_port_29"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_ground_pin_defined_warning",
"source_no_ground_pin_defined_warning_id": "source_no_ground_pin_defined_warning_source_component_7",
"warning_type": "source_no_ground_pin_defined_warning",
"message": "U2_CHARGER has no pin with requires_ground=true",
"source_component_id": "source_component_7",
"source_port_ids": [
"source_port_32",
"source_port_33",
"source_port_34",
"source_port_35",
"source_port_36",
"source_port_37",
"source_port_38",
"source_port_39",
"source_port_40",
"source_port_41",
"source_port_42",
"source_port_43",
"source_port_44",
"source_port_45",
"source_port_46",
"source_port_47",
"source_port_48",
"source_port_49",
"source_port_50",
"source_port_51"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_ground_pin_defined_warning",
"source_no_ground_pin_defined_warning_id": "source_no_ground_pin_defined_warning_source_component_19",
"warning_type": "source_no_ground_pin_defined_warning",
"message": "U3_GAUGE has no pin with requires_ground=true",
"source_component_id": "source_component_19",
"source_port_ids": [
"source_port_76",
"source_port_77",
"source_port_78",
"source_port_79",
"source_port_80",
"source_port_81",
"source_port_82",
"source_port_83",
"source_port_84"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_ground_pin_defined_warning",
"source_no_ground_pin_defined_warning_id": "source_no_ground_pin_defined_warning_source_component_25",
"warning_type": "source_no_ground_pin_defined_warning",
"message": "U1_MCU has no pin with requires_ground=true",
"source_component_id": "source_component_25",
"source_port_ids": [
"source_port_95",
"source_port_96",
"source_port_97",
"source_port_98",
"source_port_99",
"source_port_100",
"source_port_101",
"source_port_102",
"source_port_103",
"source_port_104",
"source_port_105",
"source_port_106",
"source_port_107",
"source_port_108",
"source_port_109",
"source_port_110",
"source_port_111",
"source_port_112",
"source_port_113",
"source_port_114",
"source_port_115",
"source_port_116",
"source_port_117",
"source_port_118",
"source_port_119"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_ground_pin_defined_warning",
"source_no_ground_pin_defined_warning_id": "source_no_ground_pin_defined_warning_source_component_26",
"warning_type": "source_no_ground_pin_defined_warning",
"message": "J4_SWD has no pin with requires_ground=true",
"source_component_id": "source_component_26",
"source_port_ids": [
"source_port_120",
"source_port_121",
"source_port_122",
"source_port_123",
"source_port_124",
"source_port_125",
"source_port_126"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_ground_pin_defined_warning",
"source_no_ground_pin_defined_warning_id": "source_no_ground_pin_defined_warning_source_component_27",
"warning_type": "source_no_ground_pin_defined_warning",
"message": "Q1_DISPLAY_SWITCH has no pin with requires_ground=true",
"source_component_id": "source_component_27",
"source_port_ids": [
"source_port_127",
"source_port_128",
"source_port_129"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_ground_pin_defined_warning",
"source_no_ground_pin_defined_warning_id": "source_no_ground_pin_defined_warning_source_component_28",
"warning_type": "source_no_ground_pin_defined_warning",
"message": "Y1_48MHZ has no pin with requires_ground=true",
"source_component_id": "source_component_28",
"source_port_ids": [
"source_port_130",
"source_port_131",
"source_port_132",
"source_port_133"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_ground_pin_defined_warning",
"source_no_ground_pin_defined_warning_id": "source_no_ground_pin_defined_warning_source_component_40",
"warning_type": "source_no_ground_pin_defined_warning",
"message": "U4_ACCEL has no pin with requires_ground=true",
"source_component_id": "source_component_40",
"source_port_ids": [
"source_port_156",
"source_port_157",
"source_port_158",
"source_port_159",
"source_port_160",
"source_port_161",
"source_port_162",
"source_port_163",
"source_port_164",
"source_port_165",
"source_port_166",
"source_port_167"
],
"subcircuit_id": "subcircuit_source_group_4"
},
{
"type": "source_no_ground_pin_defined_warning",
"source_no_ground_pin_defined_warning_id": "source_no_ground_pin_defined_warning_source_component_50",
"warning_type": "source_no_ground_pin_defined_warning",
"message": "ANT1 has no pin with requires_ground=true",
"source_component_id": "source_component_50",
"source_port_ids": [
"source_port_186",
"source_port_187"
],
"subcircuit_id": "subcircuit_source_group_4"
}
]
}
Related Packages
More from this authorseveibar/spi-display-webcam-interceptorThis collection of code defines various hardware components, including an crystal oscillator, microcontroller, voltage regulators, inductors, connectors, and logic gates, each represented with physical footprint, pin configurations, and 3D CAD models for PCB design and integration.
Similar packageaura/diy-power-delivery-triggerThis hardware design implements a USB Type-C port with supporting power management and signal conditioning components, including a USB-C connector, a FUSB302 USB-C port controller, ESD protection diodes, a buck converter for 3.3V power regulation, an STM32 microcontroller for control and processing, an RGB LED indicator, push button, terminal block connections, and associated filtering and support components.
Discover something newShiboSoftwareDev/mspm0g3507-usb-c-dev-boardThe circuit assembles a USB-C port with integrated ESD protection, power regulation, UART interface, and microcontroller (MSPM0G3507) with supporting components for USB data lines, CC termination, I2C, SPI, reset circuitry, and indicator LEDs.