muse/book-reading-clip-lamp
A tscircuit package created by muse.
- Version
- 0.4.6
- License
- unset
- Stars
- 0
base-catalog-parts.json
{
"revision": "M12",
"date": "2026-11-03",
"units": "mm",
"modelProvenance": "Authored drawing-based external models; not certified vendor STEP. Critical envelopes and panel/hinge interfaces follow listed sources; clamps, contacts, molded radii, thread helices and wire poses simplified.",
"parts": [
{
"ref": "BAT1",
"qty": 1,
"part": "2011 / PKCELL 803860 protected pack",
"maker": "Adafruit",
"url": "https://www.adafruit.com/product/2011",
"drawing": "https://cdn-shop.adafruit.com/datasheets/LiIon2000mAh37V.pdf",
"dims": [
38.5,
62,
8.5
],
"status": "MECHANICAL CANDIDATE; charging temperature mismatch",
"note": "1S 3.7 V 2000 mAh; 4.2 V charge; 2 A maximum discharge. Manufacturer maximum dimensions include PCM; retail headline is smaller. Cell charge range 0–45 C; existing direct 103AT TS window approximately 0–50 C must be corrected/qualified before battery charging."
},
{
"ref": "BAT_EXT",
"qty": 1,
"part": "3814",
"maker": "Adafruit",
"url": "https://www.adafruit.com/product/3814",
"drawing": "https://www.adafruit.com/product/3814",
"dims": null,
"status": "Stock 200 mm male PH2-to-wire pigtail; confirm delivered lead gauge/polarity",
"note": "Replaces 500 mm 1131 extension. Factory male PH2 header mates the unchanged battery plug; opposite end is supplied as bare wires. Trim/strip free ends for WAGO; no extra connector or custom battery adapter. Model uses 0.9 mm lead OD as a fit assumption; verify delivered insulation/current rating."
},
{
"ref": "SW1",
"qty": 1,
"part": "1445",
"maker": "Adafruit",
"url": "https://www.adafruit.com/product/1445",
"drawing": "https://cdn-shop.adafruit.com/datasheets/R16diagram.jpg",
"dims": [
18,
18,
30.3
],
"status": "Prototype candidate; test dry logic contacts",
"note": "16 mm panel momentary normally open; drawing maximum depth 30.3 mm versus store 29.4 mm. Use drawing envelope and actual supplier sample. ASK_REMOTE to GND."
},
{
"ref": "SW3",
"qty": 1,
"part": "1442",
"maker": "Adafruit",
"url": "https://www.adafruit.com/product/1442",
"drawing": "https://cdn-shop.adafruit.com/datasheets/R16diagram.jpg",
"dims": [
18,
18,
30.3
],
"status": "Prototype candidate; test dry logic contacts",
"note": "16 mm latching button. CLOSED/latched is OFF/charge, OPEN is ON with existing PCB logic. Independent LED tabs not connected; cap individually. Not battery isolation."
},
{
"ref": "SW_LEADS",
"qty": 1,
"part": "1152 (10 pairs; use 2 pairs)",
"maker": "Adafruit",
"url": "https://www.adafruit.com/product/1152",
"drawing": "https://cdn-shop.adafruit.com/datasheets/quickconnect110.pdf",
"dims": null,
"status": "Stock precrimped leads; equivalent terminal drawing only",
"note": "0.110 inch quick-connect female sockets, 200 mm 22 AWG leads. Keep quick-connects; cut off opposite JST connector, trim and strip for WAGO. Drawing linked by supplier is an equivalent terminal, not a guaranteed TE terminal identity."
},
{
"ref": "BASE_SPLICE",
"qty": 5,
"part": "222-412",
"maker": "WAGO",
"url": "https://www.digikey.com/en/products/detail/wago-corporation/222-412/13549446",
"drawing": "https://www.wago.com/us/wire-splicing-connectors/splicing-connector/p/222-412",
"dims": [
12.4,
20.5,
14.5
],
"status": "Stock 2-wire single-potential lever splice",
"note": "One block EACH for VBAT, NTC sense, NTC dedicated return, ASK_REMOTE and PWR_REMOTE. 28–12 AWG; strip 9–10 mm; ONE potential per entire block, never two different nets. Lever access with cradle removed."
},
{
"ref": "BASE_GND",
"qty": 1,
"part": "222-415",
"maker": "WAGO",
"url": "https://www.digikey.com/en/products/detail/wago-corporation/222-415/13549571",
"drawing": "https://www.wago.com/us/wire-splicing-connectors/splicing-connector/p/222-415",
"dims": [
26.6,
20.5,
14.5
],
"status": "Stock 5-wire single-potential lever splice",
"note": "Head J3.2, battery negative, Chat return and power return; fifth cavity unused. Do not tie SPK_N here. Do not replace with 221 without checking minimum wire size."
},
{
"ref": "SPK1",
"qty": 1,
"part": "CES-30207-158L120-67",
"maker": "Same Sky",
"url": "https://www.sameskydevices.com/product/resource/ces-30207-158l120-67.pdf",
"drawing": "https://www.sameskydevices.com/product/resource/ces-30207-158l120-67.pdf",
"dims": [
30.5,
20.2,
7.2
],
"status": "Already ordered; retained",
"note": "8 ohm 1.5 W, nominal body 30 x 20 x 7. 120 +/-5 mm supplied 30 AWG lead and Molex 51021-0200 female connector. Do not cut supplied speaker cable. Limit amplifier power in firmware."
},
{
"ref": "SPK_EXT",
"qty": 1,
"part": "2181130204",
"maker": "Molex",
"url": "https://www.newark.com/molex/218113-0204/cable-assy-2pos-rcpt-plug-425mm/dp/66AJ9504",
"drawing": "https://www.molex.com/content/dam/molex/molex-dot-com/products/automated/en-us/salesdrawingpdf/218/218113/2181130204_sd.pdf",
"dims": null,
"status": "Catalog 425 mm preassembled PicoBlade plug-to-socket cable; check delivery at order",
"note": "Keep male 51047 speaker end. Cut off opposite female connector, thread 28 AWG wires through neck, then fit XH contacts at head. Modeled run fits within 425 +/-8 mm. Determine speaker polarity by continuity: vendor drawing crosses cavity numbers. Stock cable needs head-end termination, no extra base splice. DigiKey US page currently shows zero stock; Newark lists UK-stock delivery."
},
{
"ref": "NTC1",
"qty": 1,
"part": "103AT-11",
"maker": "Semitec",
"url": "https://www.digikey.com/en/products/detail/semitec-usa-corp/103AT-11/16578928",
"drawing": "https://www.semitec-global.com/uploads/2022/01/P12-13-AT-Thermistor.pdf",
"dims": [
5,
15,
6.2
],
"status": "Stock factory prewired thermistor; new sourcing option replaces bare 103AT-2 in this model",
"note": "10k ohm 1%, B25/85 3435 K 1%, matching the old nominal electrical curve. Factory insulated parallel leads 600 +20/-0 mm; trim/split/strip into separate WAGO sense/return blocks. No custom thermistor solder joints. Protected body 15 mm maximum length x6.2 width x5 thickness, mounted at cell side. Lead OD1.8 mm is a conservative fit assumption; confirm shipped cable. Mounting/thermal response still need qualification; battery 45 C versus current approximately50 C hot cutoff hold remains. Already-owned 103AT-2 remains usable only with a prepared insulated extension; not the minimum-soldering version shown."
},
{
"ref": "SPRING1",
"qty": 1,
"part": "TMR-0304-035",
"maker": "WB Jones",
"url": "https://www.springsfast.com/products/torsion-springs/",
"drawing": "https://www.springsfast.com/products/torsion-springs/",
"dims": null,
"status": "Catalog spring candidate; installed force and travel unqualified",
"note": "Right hand music wire; 0.304 inch OD, 0.035 inch wire, 7 coils, 1.250 inch legs, 180 degree catalog deflection. Model assumes 160 degree preload and approximate deformed coil; not a force simulation. Confirm free angle, wound direction and 4.75 mm rod recommendation with supplier before purchase."
},
{
"ref": "HINGE_BOLT",
"qty": 1,
"part": "SSC-M4-70-A2",
"maker": "Accu",
"url": "https://www.accu.co.uk/metric-cap-head-screws/2838-SSC-M4-70-A2",
"drawing": "https://www.accu.co.uk/metric-cap-head-screws/2838-SSC-M4-70-A2",
"dims": null,
"status": "Standard M4 x 70 DIN 912 prototype hinge",
"note": "70 mm under head, 7 mm head OD, 4 mm head height, 3 mm hex, minimum 20 mm thread. Threads may be in right bearing: qualify wear and free rotation; not a shoulder bolt."
},
{
"ref": "HINGE_WASHER",
"qty": 2,
"part": "HPW-M4-A2-BL",
"maker": "Accu",
"url": "https://www.accu.co.uk/metric-flat-washers/179355-HPW-M4-A2-BL",
"drawing": "https://www.accu.co.uk/metric-flat-washers/179355-HPW-M4-A2-BL",
"dims": [
9,
4.3,
0.9
],
"status": "DIN 125 M4 washer; model uses maximum thickness",
"note": "9 mm OD, 4.3 mm ID, 0.9 mm maximum thickness. Vendor stock to confirm at order."
},
{
"ref": "HINGE_NUT",
"qty": 1,
"part": "HNN-M4-A2",
"maker": "Accu",
"url": "https://www.accu.co.uk/hexagon-nylon-locking-nuts/7946-HNN-M4-A2",
"drawing": "https://www.accu.co.uk/hexagon-nylon-locking-nuts/7946-HNN-M4-A2",
"dims": [
7,
7,
5
],
"status": "DIN 985 M4 locking nut",
"note": "7 mm across flats, 5 mm nominal overall height. Threads simplified as clearance in model. Adjust for running clearance; do not tighten until jaws lock."
},
{
"ref": "BASE_LID_SCREWS",
"qty": 4,
"part": "SSCF-M2-6-A2",
"maker": "Accu",
"url": "https://www.accu.co.uk/metric-cap-head-screws/3792-SSCF-M2-6-A2",
"drawing": "https://www.accu.co.uk/metric-cap-head-screws/3792-SSCF-M2-6-A2",
"dims": null,
"status": "DIN 912 M2 catalog fastener; trial printed threads",
"note": "M2 x 6 mm under head; 3.8 mm head OD, 2 mm head height, 1.5 mm hex. Thread helices omitted; root modeled inside printed pilot. Use measured/tapped M2 pilots and verify torque."
},
{
"ref": "SPK_CRADLE_SCREWS",
"qty": 2,
"part": "SSCF-M2-4-A2",
"maker": "Accu",
"url": "https://www.accu.co.uk/metric-cap-head-screws/3790-SSCF-M2-4-A2",
"drawing": "https://www.accu.co.uk/metric-cap-head-screws/3790-SSCF-M2-4-A2",
"dims": null,
"status": "DIN 912 M2 catalog fastener; trial printed threads",
"note": "M2 x 4 mm under head; 3.8 mm head OD, 2 mm head height, 1.5 mm hex. Thread helices omitted; root modeled inside printed pilot. Use measured/tapped M2 pilots and verify torque."
}
],
"unresolved": [
"Battery charge temperature 45 C versus current approximately 50 C cutoff",
"Camera FPC maximum width / J2 mating hold unchanged",
"Neck supplier, load capacity and wire OD/bend life unqualified",
"Spring preload, direction, grip force, travel and jaw fatigue unqualified",
"Head XHP-8 termination, actual cable OD/current ratings and strain relief still need qualification"
]
}
Related Packages
More from this authormuse/esp32-eink-displayA 55×46 mm two-layer ESP32-S3 e-paper controller board with USB‑C power/programming, buck regulation, FPC display connector, UC8179-style boost/charge-pump circuitry, ESD protection, controls, and routed passive components.
Discover something newseveibar/f1c100s-linux-dev-boardA 4-layer F1C100S Linux development carrier board with USB‑C power/data, multi-rail LDOs, SPI NOR flash, reset/boot interfaces, I²C/SPI/UART headers, ESD protection, and a buffered 5‑V clocked RGB LED.