mohan-bee/compact-pir

validation/strict-build.log

Building 1 file(s)...
Building index.circuit.tsx...
Generating circuit JSON...
Wrote debug artifact: validation/autorouter/placement-unrouted.png
Autorouting <board#486 /> phase 1/1 start: connections=29, obstacles=311, previous_traces=0, router=tscircuit, version=beta_pipeline9, solver=AutoroutingPipelineSolver9_PreloadedTraceGraph, effort=2x, cache=miss, cache_id=8efffac3/2c7cfb9e
  connections: net.CHIP_TX, net.EN, net.GPIO0, net.GPIO1, net.GPIO10, net.GPIO18, net.GPIO19, net.GPIO2, net.GPIO3, net.GPIO4, net.GPIO5, net.GPIO6, net.GPIO7, net.GPIO8, net.GPIO9, net.LED_BASE, net.LED_NEG, net.LED_POS, net.RF_ANT, net.RF_CHIP, net.UART_TX, net.XTAL_LOAD, net.XTAL_N, net.XTAL_P, net.GND, net.VBAT, net.V3V3, net.V3V3_RF, net.PIR_VDD
Wrote debug artifact: validation/autorouter/phase-0.input.simple-route.json
  phase 1/1 progress: solver=AutoroutingPipelineSolver9_PreloadedTraceGraph solver_phase=topologyMergingSolver steps=1 progress=21% iterations_per_second=22592 elapsed=1.1s
  phase 1/1 progress: solver=AutoroutingPipelineSolver9_PreloadedTraceGraph solver_phase=highDensityRouteSolver steps=37 progress=54% iterations_per_second=9184 elapsed=11.3s
  phase 1/1 progress: solver=AutoroutingPipelineSolver9_PreloadedTraceGraph solver_phase=pipeline9JointDrcRepairSolver steps=71 progress=85% iterations_per_second=2480 elapsed=21.3s
  phase 1/1 progress: solver=AutoroutingPipelineSolver9_PreloadedTraceGraph solver_phase=pipeline9JointDrcRepairSolver steps=102 progress=87% iterations_per_second=2484 elapsed=31.3s
  phase 1/1 progress: solver=AutoroutingPipelineSolver9_PreloadedTraceGraph solver_phase=effortCleanupSolver steps=137 progress=88% iterations_per_second=5592 elapsed=41.4s
  phase 1/1 done: routed_traces=87, jumpers=0, errors=0, elapsed=42.3s
Wrote debug artifact: validation/autorouter/phase-0.output.traces.json
Wrote debug artifact: validation/autorouter/phase-0-routed.png
Could not save autorouting paths for subcircuit_source_group_0: Routes contain a junction or endpoint that cannot select a unique PCB port
Wrote debug artifact: validation/autorouter/board.meta.json
Circuit JSON written to dist/index/circuit.json
The "J" prefix is being used with a <chip />, try using it with a <connector /> or <jumper />
The "Q" prefix is being used with a <chip />, try using it with a <transistor />
J3 has no pin with requires_power=true
Q1 has no pin with requires_power=true
Q1 has no pin with requires_ground=true
All pins on Q1 are underspecified (no pinAttributes set)
No <schematicsheet> was found. Add a <schematicsheet> to define the schematic drawing area.
PCB trace .J2 > .pin4 to net.GPIO1 is too close to .J2 > .pin3 to net.GPIO0 (gap: 0.072mm)

Build complete
  Circuits  0 passed 1 failed
  Options   autorouter-debug, autorouter-timeout, autorouter-dump-srj
  Output    dist

⚠ Build completed with errors
Build exiting with code 1: circuit build errors occurred