gokul/usb3-sd-hub
Engineering draft: four-layer, computer-powered USB 3 hub with one USB-C host socket, two USB-C and two USB-A accessory sockets, and a full-size SD slot. Board and three schematic previews are available. Routing and production checks are incomplete; not fabrication ready.
- Version
- 0.1.4
- License
- unset
- Stars
- 0
imports/HD3SS3220RNHR.tsx
import { SchematicNote } from "../components/SchematicNote";
import { placementFor } from "../design/placement";
import type { ChipProps } from "@tscircuit/props";
const pinLabels = {
pin1: ["CC2"],
pin2: ["CC1"],
pin3: ["CURRENT_MODE"],
pin4: ["PORT"],
pin5: ["VBUS_DET"],
pin6: ["TXp"],
pin7: ["TXn"],
pin8: ["VCC33"],
pin9: ["RXp"],
pin10: ["RXn"],
pin11: ["DIR"],
pin12: ["ENn_MUX"],
pin13: ["GND1"],
pin14: ["RX1n"],
pin15: ["RX1p"],
pin16: ["TX1n"],
pin17: ["TX1p"],
pin18: ["RX2n"],
pin19: ["RX2p"],
pin20: ["TX2n"],
pin21: ["TX2p"],
pin22: ["ADDR"],
pin23: ["INT_N", "OUT3"],
pin24: ["VCONN_FAULT_N"],
pin25: ["SDA", "OUT1"],
pin26: ["SCL", "OUT2"],
pin27: ["ID"],
pin28: ["GND2"],
pin29: ["ENn_CC"],
pin30: ["VDD5"],
pin31: ["EP"],
} as const;
const pinAttributes = {
pin8: { requiresPower: true },
pin13: { requiresGround: true },
pin28: { requiresGround: true },
pin30: { requiresPower: true },
} as const;
export const HD3SS3220RNHR = (props: ChipProps<typeof pinLabels>) => {
return (
<chip
pinLabels={pinLabels}
pinAttributes={pinAttributes}
supplierPartNumbers={{
jlcpcb: ["C165155"],
}}
manufacturerPartNumber="HD3SS3220RNHR"
footprint={
<footprint>
<smtpad
portHints={["pin2"]}
pcbX="-1.400048mm"
pcbY="-1.199896mm"
width="0.1999996mm"
height="0.5050028mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin3"]}
pcbX="-0.999998mm"
pcbY="-1.199896mm"
width="0.1999996mm"
height="0.5050028mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin4"]}
pcbX="-0.599948mm"
pcbY="-1.199896mm"
width="0.1999996mm"
height="0.5050028mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin5"]}
pcbX="-0.199898mm"
pcbY="-1.199896mm"
width="0.1999996mm"
height="0.5050028mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin6"]}
pcbX="0.199898mm"
pcbY="-1.199896mm"
width="0.1999996mm"
height="0.5050028mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin7"]}
pcbX="0.599948mm"
pcbY="-1.199896mm"
width="0.1999996mm"
height="0.5050028mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin8"]}
pcbX="0.999998mm"
pcbY="-1.199896mm"
width="0.1999996mm"
height="0.5050028mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin9"]}
pcbX="1.400048mm"
pcbY="-1.199896mm"
width="0.1999996mm"
height="0.5050028mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin12"]}
pcbX="2.199894mm"
pcbY="-0.40005mm"
width="0.5050028mm"
height="0.1999996mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin13"]}
pcbX="2.199894mm"
pcbY="0mm"
width="0.5050028mm"
height="0.1999996mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin14"]}
pcbX="2.199894mm"
pcbY="0.40005mm"
width="0.5050028mm"
height="0.1999996mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin17"]}
pcbX="1.400048mm"
pcbY="1.199896mm"
width="0.1999996mm"
height="0.5050028mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin18"]}
pcbX="0.999998mm"
pcbY="1.199896mm"
width="0.1999996mm"
height="0.5050028mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin19"]}
pcbX="0.599948mm"
pcbY="1.199896mm"
width="0.1999996mm"
height="0.5050028mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin20"]}
pcbX="0.199898mm"
pcbY="1.199896mm"
width="0.1999996mm"
height="0.5050028mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin21"]}
pcbX="-0.199898mm"
pcbY="1.199896mm"
width="0.1999996mm"
height="0.5050028mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin22"]}
pcbX="-0.599948mm"
pcbY="1.199896mm"
width="0.1999996mm"
height="0.5050028mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin23"]}
pcbX="-0.999998mm"
pcbY="1.199896mm"
width="0.1999996mm"
height="0.5050028mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin24"]}
pcbX="-1.400048mm"
pcbY="1.199896mm"
width="0.1999996mm"
height="0.5050028mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin27"]}
pcbX="-2.199894mm"
pcbY="0.40005mm"
width="0.5050028mm"
height="0.1999996mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin28"]}
pcbX="-2.199894mm"
pcbY="0mm"
width="0.5050028mm"
height="0.1999996mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin29"]}
pcbX="-2.199894mm"
pcbY="-0.40005mm"
width="0.5050028mm"
height="0.1999996mm"
radius="0.0999998mm"
shape="pill"
/>
<smtpad
portHints={["pin31"]}
pcbX="0mm"
pcbY="0mm"
width="3.1999936mm"
height="1.1999976mm"
shape="rect"
/>
<smtpad
portHints={["pin15"]}
points={[
{ x: "2.4500078mm", y: "0.8999982mm" },
{ x: "2.4500078mm", y: "0.6999986mm" },
{ x: "1.9500088mm", y: "0.700024mm" },
{ x: "1.9500088mm", y: "0.7001256mm" },
{ x: "1.9500088mm", y: "0.8000492mm" },
{ x: "1.9500088mm", y: "0.8000492mm" },
{ x: "2.0500086mm", y: "0.8999982mm" },
]}
shape="polygon"
/>
<smtpad
portHints={["pin16"]}
points={[
{ x: "1.8999962mm", y: "1.4499844mm" },
{ x: "1.6999712mm", y: "1.4499844mm" },
{ x: "1.700022mm", y: "0.9500362mm" },
{ x: "1.7001998mm", y: "0.9500362mm" },
{ x: "1.8000218mm", y: "0.9500362mm" },
{ x: "1.8000218mm", y: "0.9500362mm" },
{ x: "1.8999962mm", y: "1.0499852mm" },
]}
shape="polygon"
/>
<smtpad
portHints={["pin1"]}
points={[
{ x: "-1.900047mm", y: "-1.4499844mm" },
{ x: "-1.700022mm", y: "-1.4499844mm" },
{ x: "-1.7000728mm", y: "-0.9500362mm" },
{ x: "-1.7002506mm", y: "-0.9500362mm" },
{ x: "-1.8000726mm", y: "-0.9500362mm" },
{ x: "-1.8000726mm", y: "-0.9500362mm" },
{ x: "-1.900047mm", y: "-1.0499852mm" },
]}
shape="polygon"
/>
<smtpad
portHints={["pin30"]}
points={[
{ x: "-2.4500332mm", y: "-0.8999728mm" },
{ x: "-2.4500332mm", y: "-0.6999986mm" },
{ x: "-1.9500596mm", y: "-0.700024mm" },
{ x: "-1.9500596mm", y: "-0.7001002mm" },
{ x: "-1.9500596mm", y: "-0.8000492mm" },
{ x: "-1.9500596mm", y: "-0.8000492mm" },
{ x: "-2.0500594mm", y: "-0.8999728mm" },
]}
shape="polygon"
/>
<smtpad
portHints={["pin26"]}
points={[
{ x: "-2.4499316mm", y: "0.8998712mm" },
{ x: "-2.4499316mm", y: "0.699897mm" },
{ x: "-1.9499326mm", y: "0.6999478mm" },
{ x: "-1.9499326mm", y: "0.7000748mm" },
{ x: "-1.9499326mm", y: "0.7999476mm" },
{ x: "-1.9499326mm", y: "0.7999476mm" },
{ x: "-2.0499832mm", y: "0.8999982mm" },
]}
shape="polygon"
/>
<smtpad
portHints={["pin25"]}
points={[
{ x: "-1.900047mm", y: "1.4499336mm" },
{ x: "-1.700022mm", y: "1.4498828mm" },
{ x: "-1.7001236mm", y: "0.9499854mm" },
{ x: "-1.7002506mm", y: "0.9499346mm" },
{ x: "-1.8000472mm", y: "0.9499346mm" },
{ x: "-1.8000472mm", y: "0.9499346mm" },
{ x: "-1.900047mm", y: "1.0498074mm" },
]}
shape="polygon"
/>
<smtpad
portHints={["pin10"]}
points={[
{ x: "1.900047mm", y: "-1.450086mm" },
{ x: "1.6999712mm", y: "-1.4500606mm" },
{ x: "1.7000474mm", y: "-0.9501378mm" },
{ x: "1.7002252mm", y: "-0.9501378mm" },
{ x: "1.7999964mm", y: "-0.9501124mm" },
{ x: "1.7999964mm", y: "-0.9501124mm" },
{ x: "1.9001232mm", y: "-1.0499852mm" },
]}
shape="polygon"
/>
<smtpad
portHints={["pin11"]}
points={[
{ x: "2.449957mm", y: "-0.899922mm" },
{ x: "2.449957mm", y: "-0.6999986mm" },
{ x: "1.9499326mm", y: "-0.6999986mm" },
{ x: "1.9499326mm", y: "-0.7001256mm" },
{ x: "1.9499326mm", y: "-0.8000492mm" },
{ x: "1.9499326mm", y: "-0.8000492mm" },
{ x: "2.0499832mm", y: "-0.899922mm" },
]}
shape="polygon"
/>
<silkscreenpath
route={[
{ x: -2.3262081999999964, y: 1.1025124000000233 },
{ x: -2.3262081999999964, y: 1.326210200000105 },
{ x: -2.1025103999999146, y: 1.326210200000105 },
]}
/>
<silkscreenpath
route={[
{ x: 2.3262081999999964, y: 1.1025124000000233 },
{ x: 2.3262081999999964, y: 1.326210200000105 },
{ x: 2.1025104000000283, y: 1.326210200000105 },
]}
/>
<silkscreenpath
route={[
{ x: -2.3262081999999964, y: -1.1025124000000233 },
{ x: -2.3262081999999964, y: -1.326210200000105 },
{ x: -2.1025103999999146, y: -1.326210200000105 },
]}
/>
<silkscreenpath
route={[
{ x: 2.3262081999999964, y: -1.1025124000000233 },
{ x: 2.3262081999999964, y: -1.326210200000105 },
{ x: 2.1025104000000283, y: -1.326210200000105 },
]}
/>
<silkscreencircle
pcbX="-1.800098mm"
pcbY="-1.729994mm"
radius="0.07493mm"
/>
<silkscreentext
text="{NAME}"
pcbX="-0.0127mm"
pcbY="2.4478mm"
anchorAlignment="center"
fontSize="1mm"
/>
<courtyardoutline
outline={[
{ x: -2.702395400000114, y: 1.702397400000109 },
{ x: 2.7023954000000003, y: 1.702397400000109 },
{ x: 2.7023954000000003, y: -1.7023973999999953 },
{ x: -2.702395400000114, y: -1.7023973999999953 },
{ x: -2.702395400000114, y: 1.702397400000109 },
]}
/>
</footprint>
}
cadModel={{
objUrl:
"https://modelcdn.tscircuit.com/easyeda_models/assets/C165155.obj?uuid=db8cca3278554dd79dd0e7b7f825ecec",
stepUrl:
"https://modelcdn.tscircuit.com/easyeda_models/assets/C165155.step?uuid=db8cca3278554dd79dd0e7b7f825ecec",
pcbRotationOffset: 0,
modelOriginPosition: {
x: 0.000012700000070253736,
y: 0.000012699999842880061,
z: -0.025,
},
}}
{...props}
{...placementFor(props.name)}
>
<SchematicNote
text={"USB-C orientation / CC control\n3.3 V logic; 5 V supply; 5 Gbps"}
/>
</chip>
);
};
Related Packages
More from this authorgokul/led-blinkingThis design implements a hardware LED blink circuit using a 555 timer IC connected with resistors, capacitors, an LED, and header pins for power input.
Similar packagepixalynx/usb3-hub-10gA USB 3.2 Gen 2 six-port hub board with USB-C PD power input, regulated 5 V/3.3 V/1.15 V rails, one upstream and four protected downstream USB-A/USB-C ports, SuperSpeed muxes, ESD protection, and controlled port power.
Discover something newrushabhcodes/ESP32-E-ReaderA compact ESP32-C3 board with USB-C power/charging, Li-ion battery protection, 3.3-V regulation, e-paper and microSD interfaces, and user buttons/switches.