AnasSarkiz/rp2040-bldc-servo-controller
RP2040-based motor-control board integrating a DRV8316 three-phase gate driver, AS5047P magnetic position sensor, USB-C power/communications, STUSB4500 USB-PD controller, SPI flash, and THVD1450 RS-485 transceiver.
- Version
- 0.0.5
- License
- unset
- Stars
- 0
imports/STUSB4500QTR/STUSB4500QTR.tsx
import objPath from "./STUSB4500QTR.obj"
import stepPath from "./STUSB4500QTR.step"
import { type ChipProps } from "tscircuit"
const pinLabels = {
"pin1": [
"CC1DB"
],
"pin2": [
"CC1"
],
"pin3": [
"NC"
],
"pin4": [
"CC2"
],
"pin5": [
"CC2DB"
],
"pin6": [
"RESET"
],
"pin7": [
"SCL"
],
"pin8": [
"SDA"
],
"pin9": [
"DISCH"
],
"pin10": [
"GND"
],
"pin11": [
"ATTACH"
],
"pin12": [
"ADDR0"
],
"pin13": [
"ADDR1"
],
"pin14": [
"POWER_OK3"
],
"pin15": [
"GPIO"
],
"pin16": [
"VBUS_EN_SNK"
],
"pin17": [
"A_B_SIDE"
],
"pin18": [
"VBUS_VS_DISCH"
],
"pin19": [
"ALERT"
],
"pin20": [
"POWER_OK2"
],
"pin21": [
"VREG_1V2"
],
"pin22": [
"VSYS"
],
"pin23": [
"VREG_2V7"
],
"pin24": [
"VDD"
],
"pin25": [
"EP"
]
} as const
export const STUSB4500QTR = (props: ChipProps<typeof pinLabels>) => (
<chip
footprint={<footprint>
<smtpad portHints={["pin1"]} pcbX="-1.249934000000053mm" pcbY="-1.99999600000001mm" layer="top" width="0.2800096mm" height="0.6999986mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin2"]} pcbX="-0.7500620000000708mm" pcbY="-1.99999600000001mm" layer="top" width="0.2800096mm" height="0.6999986mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin3"]} pcbX="-0.2499359999999342mm" pcbY="-1.99999600000001mm" layer="top" width="0.2800096mm" height="0.6999986mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin4"]} pcbX="0.24993599999982052mm" pcbY="-1.99999600000001mm" layer="top" width="0.2800096mm" height="0.6999986mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin5"]} pcbX="0.7500619999999572mm" pcbY="-1.99999600000001mm" layer="top" width="0.2800096mm" height="0.6999986mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin6"]} pcbX="1.2499339999999393mm" pcbY="-1.99999600000001mm" layer="top" width="0.2800096mm" height="0.6999986mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin7"]} pcbX="1.9999960000001238mm" pcbY="-1.249934000000053mm" layer="top" width="0.6999986mm" height="0.2800096mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin8"]} pcbX="1.9999960000001238mm" pcbY="-0.7500619999999572mm" layer="top" width="0.6999986mm" height="0.2800096mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin9"]} pcbX="1.9999960000001238mm" pcbY="-0.2499360000000479mm" layer="top" width="0.6999986mm" height="0.2800096mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin10"]} pcbX="1.9999960000001238mm" pcbY="0.2499360000000479mm" layer="top" width="0.6999986mm" height="0.2800096mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin11"]} pcbX="1.9999960000001238mm" pcbY="0.7500620000001845mm" layer="top" width="0.6999986mm" height="0.2800096mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin12"]} pcbX="1.9999960000001238mm" pcbY="1.249934000000053mm" layer="top" width="0.6999986mm" height="0.2800096mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin13"]} pcbX="1.2499339999999393mm" pcbY="1.99999600000001mm" layer="top" width="0.2800096mm" height="0.6999986mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin14"]} pcbX="0.7500619999999572mm" pcbY="1.99999600000001mm" layer="top" width="0.2800096mm" height="0.6999986mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin15"]} pcbX="0.24993599999982052mm" pcbY="1.99999600000001mm" layer="top" width="0.2800096mm" height="0.6999986mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin16"]} pcbX="-0.2499359999999342mm" pcbY="1.99999600000001mm" layer="top" width="0.2800096mm" height="0.6999986mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin17"]} pcbX="-0.7500620000000708mm" pcbY="1.99999600000001mm" layer="top" width="0.2800096mm" height="0.6999986mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin18"]} pcbX="-1.249934000000053mm" pcbY="1.99999600000001mm" layer="top" width="0.2800096mm" height="0.6999986mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin19"]} pcbX="-1.99999600000001mm" pcbY="1.249934000000053mm" layer="top" width="0.6999986mm" height="0.2800096mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin20"]} pcbX="-1.99999600000001mm" pcbY="0.7500620000001845mm" layer="top" width="0.6999986mm" height="0.2800096mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin21"]} pcbX="-1.99999600000001mm" pcbY="0.2499360000000479mm" layer="top" width="0.6999986mm" height="0.2800096mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin22"]} pcbX="-1.99999600000001mm" pcbY="-0.2499360000000479mm" layer="top" width="0.6999986mm" height="0.2800096mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin23"]} pcbX="-1.99999600000001mm" pcbY="-0.7500619999999572mm" layer="top" width="0.6999986mm" height="0.2800096mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin24"]} pcbX="-1.99999600000001mm" pcbY="-1.249934000000053mm" layer="top" width="0.6999986mm" height="0.2800096mm" radius="0.1400048mm" shape="pill" />
<smtpad portHints={["pin25"]} pcbX="0.01269999999999527mm" pcbY="0mm" layer="top" width="2.7999944mm" height="2.7999944mm" shape="rect" />
<silkscreenpath route={[{"x":2.1628099999998085,"y":1.7500345999999354},{"x":2.1628099999998085,"y":2.1501353999999537},{"x":1.7627599999999575,"y":2.1501353999999537}]} strokeWidth={0.19999959999999997} />
<silkscreenpath route={[{"x":-2.137384599999905,"y":1.7500345999999354},{"x":-2.137384599999905,"y":2.1501353999999537},{"x":-1.737359999999967,"y":2.1501353999999537}]} strokeWidth={0.19999959999999997} />
<silkscreenpath route={[{"x":-1.737359999999967,"y":-2.1501353999999537},{"x":-2.137384599999905,"y":-2.1501353999999537},{"x":-2.137384599999905,"y":-1.750085399999989}]} strokeWidth={0.19999959999999997} />
<silkscreenpath route={[{"x":2.1628099999998085,"y":-1.750085399999989},{"x":2.1628099999998085,"y":-2.1501353999999537},{"x":1.7627599999999575,"y":-2.1501353999999537}]} strokeWidth={0.19999959999999997} />
<courtyardoutline outline={[{"x":-2.599995300000046,"y":2.599995300000046},{"x":2.5999953000001597,"y":2.599995300000046},{"x":2.5999953000001597,"y":-2.599995300000046},{"x":-2.599995300000046,"y":-2.599995300000046},{"x":-2.599995300000046,"y":2.599995300000046}]} layer="top" />
</footprint>}
pinLabels={pinLabels}
pinAttributes={{
"pin1": {
"isBidirectional": true
},
"pin2": {
"isBidirectional": true
},
"pin3": {
"doNotConnect": true
},
"pin4": {
"isBidirectional": true
},
"pin5": {
"isBidirectional": true
},
"pin6": {
"isInput": true
},
"pin7": {
"isInput": true,
"needsExternalPullup": true,
"capabilities": [
"i2c_scl"
]
},
"pin8": {
"isBidirectional": true,
"needsExternalPullup": true,
"canUseOpenDrain": true,
"capabilities": [
"i2c_sda"
]
},
"pin9": {
"isBidirectional": true,
"canUseOpenDrain": true
},
"pin10": {
"requiresGround": true
},
"pin11": {
"isOutput": true,
"needsExternalPullup": true,
"canUseOpenDrain": true
},
"pin12": {
"isInput": true
},
"pin13": {
"isInput": true
},
"pin14": {
"isOutput": true,
"needsExternalPullup": true,
"canUseOpenDrain": true
},
"pin15": {
"isOutput": true,
"needsExternalPullup": true,
"canUseOpenDrain": true
},
"pin16": {
"isOutput": true,
"needsExternalPullup": true,
"canUseOpenDrain": true
},
"pin17": {
"isOutput": true,
"needsExternalPullup": true,
"canUseOpenDrain": true
},
"pin18": {
"isBidirectional": true
},
"pin19": {
"isOutput": true,
"needsExternalPullup": true,
"canUseOpenDrain": true
},
"pin20": {
"isOutput": true,
"needsExternalPullup": true,
"canUseOpenDrain": true
},
"pin21": {
"isOutput": true,
"providesVoltage": "1.2V",
"shouldHaveDecouplingCapacitor": true,
"recommendedDecouplingCapacitorCapacitance": "1uF"
},
"pin22": {
"requiresPower": true
},
"pin23": {
"isOutput": true,
"providesVoltage": "2.7V",
"shouldHaveDecouplingCapacitor": true,
"recommendedDecouplingCapacitorCapacitance": "1uF"
},
"pin24": {
"requiresPower": true
},
"pin25": {
"requiresGround": true
}
}}
supplierPartNumbers={{
"jlcpcb": [
"C2678061"
]
}}
manufacturerPartNumber="STUSB4500QTR"
cadModel={{
objUrl: objPath,
stepUrl: stepPath,
pcbRotationOffset: 0,
modelOriginPosition: {"x":-0.000012699999842880061,"y":-0.000012700000070253736,"z":0},
}}
{...props}
/>
)Related Packages
More from this authorAnasSarkiz/vibe_GoblinThese code snippets define various physical electronic components such as ICs, connectors, sensors, LEDs, and chips, specifying their pin layouts, footprint pads, silkscreen markings, courtyard outlines, and 3D CAD models for placement on PCB boards.
Similar packageMustafaMulla29/rp2040-bldc-motor-controller-new73×72 mm 4-layer USB‑C PD (5/9/15/20 V) RP2040 controller PCB with protected power switching, MCT8329A sensorless BLDC three-phase MOSFET bridge, USB data/programming, onboard controls, and three motor outputs feeding a 2212 motor through rigid bullet adapters.
Discover something newastra/nema17-stepper-motor-controller-spring-clamp-rp2040A 4-layer RP2040 controller board that negotiates USB‑C PD motor power and drives a NEMA17 stepper via a DRV8825, with current sensing, thermal shutdown, RGB status LED, buzzer alarm, optional AS5600 encoder, protection/filtering, and test points.