abse/smart-ring-flex
A tscircuit package created by abse.
- Version
- 0.0.24
- License
- unset
- Stars
- 0
firmware/onboard-programmer/upstream/src/system.h
// ===================================================================================
// Basic System Functions for CH551, CH552 and CH554 * v1.6 *
// ===================================================================================
//
// System clock (CLK)functions available:
// --------------------------------------
// CLK_config() set system clock frequency according to F_CPU
// CLK_external() set external crystal as clock source
// CLK_internal() set internal oscillator as clock source
//
// Watchdog Timer (WDT) functions available:
// -----------------------------------------
// WDT_start() start watchdog timer with full period
// WDT_stop() stop watchdog timer
// WDT_reset() reload watchdog timer with full period
// WDT_set(time) reload watchdog timer with specified time in ms
// WDT_feed(value) reload watchdog timer with specified value
//
// Reset (RST) and bootloader functions available:
// -----------------------------------------------
// RST_now() perform software reset
// RST_keep(value) keep this value after RESET
// RST_getKeep() read the keeped value
// RST_wasWDT() check if last RESET was caused by watchdog timer
// RST_wasPIN() check if last RESET was caused by RST PIN
// RST_wasPWR() check if last RESET was caused by power-on
// RST_wasSOFT() check if last RESET was caused by software
//
// BOOT_now() enter bootloader
//
// Sleep functions available:
// --------------------------
// SLEEP_now() put device into sleep
//
// WAKE_enable(source) enable wake-up from sleep source (sources see below)
// WAKE_disable(source) disable wake-up from sleep source
// WAKE_all_disable() disable all wake-up sources
//
// WAKE_USB_enable() enable wake-up by USB event
// WAKE_RXD0_enable() enable wake-up by RXD0 low level
// WAKE_RXD1_enable() enable wake-up by RXD1 low level
// WAKE_P13_enable() enable wake-up by pin P1.3 low level
// WAKE_P14_enable() enable wake-up by pin P1.4 low level
// WAKE_P15_enable() enable wake-up by pin P1.5 low level
// WAKE_RST_enable() enable wake-up by pin RST high level
// WAKE_INT_enable() enable wake-up by pin P3.2 edge or pin P3.3 low level
//
// WAKE_USB_disable() disable wake-up by USB event
// WAKE_RXD0_disable() disable wake-up by RXD0 low level
// WAKE_RXD1_disable() disable wake-up by RXD1 low level
// WAKE_P13_disable() disable wake-up by pin P1.3 low level
// WAKE_P14_disable() disable wake-up by pin P1.4 low level
// WAKE_P15_disable() disable wake-up by pin P1.5 low level
// WAKE_RST_disable() disable wake-up by pin RST high level
// WAKE_INT_disable() disable wake-up by pin P3.2 edge or pin P3.3 low level
//
// Wake-up from SLEEP sources:
// ---------------------------
// WAKE_USB wake-up by USB event
// WAKE_RXD0 wake-up by RXD0 low level
// WAKE_RXD1 wake-up by RXD1 low level
// WAKE_P13 wake-up by pin P1.3 low level
// WAKE_P14 wake-up by pin P1.4 low level
// WAKE_P15 wake-up by pin P1.5 low level
// WAKE_RST wake-up by pin RST high level
// WAKE_INT wake-up by pin P3.2 edge or pin P3.3 low level
//
// Interrupt (INT) functions available:
// ------------------------------------
// INT_enable() global interrupt enable
// INT_disable() global interrupt disable
// INT_ATOMIC_BLOCK { } execute block without being interrupted
//
// 2023 by Stefan Wagner: https://github.com/wagiminator
#pragma once
#include <stdint.h>
#include "ch554.h"
// ===================================================================================
// System Clock (CLK) Functions
// ===================================================================================
inline void CLK_config(void) {
SAFE_MOD = 0x55;
SAFE_MOD = 0xAA; // enter safe mode
#if F_CPU == 32000000
__asm__("orl _CLOCK_CFG, #0b00000111"); // 32MHz
#elif F_CPU == 24000000
__asm__("anl _CLOCK_CFG, #0b11111000");
__asm__("orl _CLOCK_CFG, #0b00000110"); // 24MHz
#elif F_CPU == 16000000
__asm__("anl _CLOCK_CFG, #0b11111000");
__asm__("orl _CLOCK_CFG, #0b00000101"); // 16MHz
#elif F_CPU == 12000000
__asm__("anl _CLOCK_CFG, #0b11111000");
__asm__("orl _CLOCK_CFG, #0b00000100"); // 12MHz
#elif F_CPU == 6000000
__asm__("anl _CLOCK_CFG, #0b11111000");
__asm__("orl _CLOCK_CFG, #0b00000011"); // 6MHz
#elif F_CPU == 3000000
__asm__("anl _CLOCK_CFG, #0b11111000");
__asm__("orl _CLOCK_CFG, #0b00000010"); // 3MHz
#elif F_CPU == 750000
__asm__("anl _CLOCK_CFG, #0b11111000");
__asm__("orl _CLOCK_CFG, #0b00000001"); // 750kHz
#elif F_CPU == 187500
__asm__("anl _CLOCK_CFG, #0b11111000"); // 187.5kHz
#else
#warning F_CPU invalid or not set
#endif
SAFE_MOD = 0x00; // terminate safe mode
}
inline void CLK_external(void) {
SAFE_MOD = 0x55;
SAFE_MOD = 0xAA; // enter safe mode
CLOCK_CFG |= bOSC_EN_XT; // enable external crystal
CLOCK_CFG &= ~bOSC_EN_INT; // turn off internal oscillator
SAFE_MOD = 0x00; // terminate safe mode
}
inline void CLK_inernal(void) {
SAFE_MOD = 0x55;
SAFE_MOD = 0xAA; // enter safe mode
CLOCK_CFG |= bOSC_EN_INT; // turn on internal oscillator
CLOCK_CFG &= ~bOSC_EN_XT; // disable external crystal
SAFE_MOD = 0x00; // terminate safe mode
}
// ===================================================================================
// Watchdog Timer (WDT) Functions
// ===================================================================================
#define WDT_reset() WDOG_COUNT = 0
#define WDT_feed(value) WDOG_COUNT = value
#define WDT_set(time) WDOG_COUNT = (uint8_t)(256 - ((F_CPU / 1000) * time / 65536))
inline void WDT_start(void) {
WDOG_COUNT = 0;
SAFE_MOD = 0x55;
SAFE_MOD = 0xAA;
GLOBAL_CFG |= bWDOG_EN;
SAFE_MOD = 0x00;
}
inline void WDT_stop(void) {
SAFE_MOD = 0x55;
SAFE_MOD = 0xAA;
GLOBAL_CFG &= ~bWDOG_EN;
SAFE_MOD = 0x00;
}
// ===================================================================================
// Reset (RST) Functions
// ===================================================================================
#define RST_keep(value) RESET_KEEP = value
#define RST_getKeep() (RESET_KEEP)
#define RST_wasWDT() ((PCON & MASK_RST_FLAG) == RST_FLAG_WDOG)
#define RST_wasPIN() ((PCON & MASK_RST_FLAG) == RST_FLAG_PIN)
#define RST_wasPWR() ((PCON & MASK_RST_FLAG) == RST_FLAG_POR)
#define RST_wasSOFT() ((PCON & MASK_RST_FLAG) == RST_FLAG_SW)
inline void RST_now(void) {
SAFE_MOD = 0x55;
SAFE_MOD = 0xAA;
GLOBAL_CFG |= bSW_RESET;
}
// ===================================================================================
// Bootloader (BOOT) Functions
// ===================================================================================
inline void BOOT_now(void) {
__asm
ljmp #BOOT_LOAD_ADDR
__endasm;
}
inline void BOOT_prepare(void) {
ES = 0;
PS = 0;
TMOD = 0;
P1_DIR_PU = 0;
P1_MOD_OC = 0;
P1 = 0xFF;
USB_INT_EN = 0;
USB_CTRL = 0x06;
EA = 0;
}
// ===================================================================================
// Sleep Functions
// ===================================================================================
#define SLEEP_now() PCON |= PD
#define WAKE_USB bWAK_BY_USB // wake-up by USB event
#define WAKE_RXD0 bWAK_RXD0_LO // wake-up by RXD0 low level
#define WAKE_RXD1 bWAK_RXD1_LO // wake-up by RXD1 low level
#define WAKE_P13 bWAK_P1_3_LO // wake-up by pin P1.3 low level
#define WAKE_P14 bWAK_P1_4_LO // wake-up by pin P1.4 low level
#define WAKE_P15 bWAK_P1_5_LO // wake-up by pin P1.5 low level
#define WAKE_RST bWAK_RST_HI // wake-up by pin RST high level
#define WAKE_INT bWAK_P3_2E_3L // wake-up by pin P3.2 (INT0) edge or pin P3.3 (INT1) low level
#define WAKE_enable(source) WAKE_CTRL |= source
#define WAKE_disable(source) WAKE_CTRL &= ~source
#define WAKE_all_disable() WAKE_CTRL = 0
#define WAKE_USB_enable() WAKE_CTRL |= bWAK_BY_USB
#define WAKE_RXD0_enable() WAKE_CTRL |= bWAK_RXD0_LO
#define WAKE_RXD1_enable() WAKE_CTRL |= bWAK_RXD1_LO
#define WAKE_P13_enable() WAKE_CTRL |= bWAK_P1_3_LO
#define WAKE_P14_enable() WAKE_CTRL |= bWAK_P1_4_LO
#define WAKE_P15_enable() WAKE_CTRL |= bWAK_P1_5_LO
#define WAKE_RST_enable() WAKE_CTRL |= bWAK_RST_HI
#define WAKE_INT_enable() WAKE_CTRL |= bWAK_P3_2E_3L
#define WAKE_USB_disable() WAKE_CTRL &= ~bWAK_BY_USB
#define WAKE_RXD0_disable() WAKE_CTRL &= ~bWAK_RXD0_LO
#define WAKE_RXD1_disable() WAKE_CTRL &= ~bWAK_RXD1_LO
#define WAKE_P13_disable() WAKE_CTRL &= ~bWAK_P1_3_LO
#define WAKE_P14_disable() WAKE_CTRL &= ~bWAK_P1_4_LO
#define WAKE_P15_disable() WAKE_CTRL &= ~bWAK_P1_5_LO
#define WAKE_RST_disable() WAKE_CTRL &= ~bWAK_RST_HI
#define WAKE_INT_disable() WAKE_CTRL &= ~bWAK_P3_2E_3L
// ===================================================================================
// Interrupt (INT) Functions
// ===================================================================================
#define INT_enable() EA = 1
#define INT_disable() EA = 0
#define INT_ATOMIC_BLOCK for(EA=0;!EA;EA=1)
Related Packages
More from this authorabse/museair-usb-assemblyA mechanically secured SEN62 sensor carrier integrates a JLC PCB, bound GH6 harness, USB power cable, fasteners, retention hardware, and protective outer enclosure.
Discover something newShiboSoftwareDev/f1c100s-linux-gameboyRestores PCB assembly metadata by assigning part numbers, managing 3D CAD models and orientations, removing test-point bodies, and validating top-side SMT solder-paste features.